Advertisements
Advertisements
प्रश्न
An AC source rated 100 V (rms) supplies a current of 10 A (rms) to a circuit. The average power delivered by the source
(a) must be 1000 W
(b) may be 1000 W
(c) may be greater than 1000 W
(d) may be less than 1000 W
उत्तर
(b) may be 1000 W
(d) may be less than 1000 W
The average power delivered by an AC source is given by,
`P_{avg} = V_{rms}I_rms cos Ø`
Given ;
`V_rms = 100V`
`Irms = 10 A`
⇒ `P_{avg} = 1000 cos `Ø
`therefore Ø ∈ (-pi/2, pi/2)`
⇒ cos Ø ∈ (0,1),
`therefore 0 ≤ P_{avg] ≤ 1000`
APPEARS IN
संबंधित प्रश्न
An a.c. source of voltage V = V0 sin ωt is connected to a series combination of L, C, and R. Use the phasor diagram to obtain the expression for an impedance of a circuit and the phase angle between voltage and current. Find the condition when current will be in phase with the voltage. What is the circuit in this condition called?
Ajit had a high tension tower erected on his farm land. He kept complaining to the authorities to remove it as it was occupying a large portion of his land. His uncle, who was a teacher, explained to him the need for erecting these towers for efficient transmission of power. As Ajit realised its significance, he stopped complaining.
Answer the following questions:
(a) Why is it necessary to transport power at high voltage?
(b) A low power factor implies large power loss. Explain.
(c) Write two values each displayed by Ajit and his uncle.
An alternating emf of 220 V is applied to a circuit containing a resistor R having the resistance of 160Ω and a capacitor ‘C’ is series. The current is found to lead the supply voltage by an angle
`θ = tan^(-1) ("3/4")`
a) Calculate
1) The capacitive reactance
2) The impedance of the circuit
3) Current flowing in the circuit
b) If the frequency of the applied emf is 50 Hz, what is the value of the capacitance of the capacitor ‘C’?
An A.C. generator generating an emf of ε = 300 sin (100 πt) V is connected to a series combination of 16μ F capacitor, 1 H inductor and 100 Ω resistor.
Calculate :
1) An impedance of the circuit at the given frequency.
2) Resonant frequency `f_0`
3)Power factor at the resonant frequency `f_0`.
Define the quality factor in an a.c. circuit. Why should the quality factor have high value in receiving circuits? Name the factors on which it depends.
In a circuit, containing a capacitor and an AC source, the current is zero at the instant the source voltage is maximum. Is it consistent with Ohm's Law?
Can you have an AC series circuit in which there is a phase difference of (a) 180° (b) 120° between the emf and the current?
The current in a discharging LR circuit is given by i = i0 e−t/τ , where τ is the time constant of the circuit. Calculate the rms current for the period t = 0 to t = τ.
Answer the following question.
Show that an ideal inductor does not dissipate power in an ac circuit.
In previous questions 3 and 4, what is the net power absorbed by each circuit over a complete cycle. Explain your answer.
Suppose the circuit has a resistance of 15 Ω. Obtain the average power transferred to each element of the circuit, and the total power absorbed.
Quality factor and power factor both have the dimensions of ______.
The power factor of series LCR circuit when at resistance is
A 100 Ω electric iron is connected to 200 V, 50 Hz ac source. Calculate average power delivered to iron, peak power and energy spent in one minute?
An inductor of reactance 1 Ω and a resistor of 2 Ω are connected in series to the terminals of a 6 V (rms) a.c. source. The power dissipated in the circuit is ______.
An alternating current I = 14 sin (100 πt) A passes through a series combination of a resistor of 30 Ω and an inductor of `(2/(5pi))` H. Taking `sqrt2` = 1.4 calculate the power factor of the circuit.
