English
Karnataka Board PUCPUC Science Class 11

A Cube of Iron (Density = 8000 Kg M−3, Specific Heat Capacity = 470 J Kg−1 K−1) is Heated to a High Temperature and is Placed on a Large Block of Ice at 0°C. - Physics

Advertisements
Advertisements

Question

A cube of iron (density = 8000 kg m−3, specific heat capacity = 470 J kg−1 K−1) is heated to a high temperature and is placed on a large block of ice at 0°C. The cube melts the ice below it, displaces the water and sinks. In the final equilibrium position, its upper surface just goes inside the ice. Calculate the initial temperature of the cube. Neglect any loss of heat outside the ice and the cube. The density of ice = 900 kg m−3 and the latent heat of fusion of ice = 3.36 × 105 J kg−1.

Sum

Solution

Given:-

Density of the iron cube = 8000 kg m-3

Density of the ice cube = 900 kg m-3

Specific heat capacity, S = 470 J kg−1 K−1

Latent heat of fusion of ice, L = 3.36 × 105 J kg−1

Let the volume of the cube be V.

Volume of water displaced = V

Mass of cube, m = 8000 V kg

Mass of the ice melted, M = 900 V

Let the initial temperature of the iron cube be T K.

Then,

Heat gained by the ice = Heat lost by the iron cube

m × S × (T − 273) = M × L

⇒ 8000 V × 470 × (T − 273) = 900 V×( 3.36 × 105)

⇒ 376 × 104 × (T − 273) = 3024 × 105

`rArrT=(30240+102648)/376`

`rArrT=132888/376K`

`rArrT=353.425Kapprox353K`

`rArrT=353K-273K`

`rArrT=80^oC`

shaalaa.com
Measurement of Temperature
  Is there an error in this question or solution?
Chapter 3: Calorimetry - Exercises [Page 47]

APPEARS IN

HC Verma Concepts of Physics Vol. 2 [English] Class 11 and 12
Chapter 3 Calorimetry
Exercises | Q 6 | Page 47

RELATED QUESTIONS

Two absolute scales A and B have triple points of water defined to be 200 A and 350 B. What is the relation between TA and TB?


The electrical resistance in ohms of a certain thermometer varies with temperature according to the approximate law:

Ro [1 + α (– To)]

The resistance is 101.6 Ω at the triple-point of water 273.16 K, and 165.5 Ω at the normal melting point of lead (600.5 K). What is the temperature when the resistance is 123.4 Ω?


Answer the following:

The triple-point of water is a standard fixed point in modern thermometry. Why? What is wrong in taking the melting point of ice and the boiling point of water as standard fixed points (as was originally done in the Celsius scale)?


A brass wire 1.8 m long at 27 °C is held taut with little tension between two rigid supports. If the wire is cooled to a temperature of –39 °C, what is the tension developed in the wire, if its diameter is 2.0 mm? Co-efficient of linear expansion of brass = 2.0 × 10–5 K–1; Young’s modulus of brass = 0.91 × 1011 Pa.


Consider the following statements.
(A) The coefficient of linear expansion has dimension K–1.
(B) The coefficient of volume expansion has dimension K–1.


Which of the following pairs represent units of the same physical quantity?


The pressure measured by a constant volume gas thermometer is 40 kPa at the triple point of water. What will be the pressure measured at the boiling point of water (100°C)?


The pressure of the gas in a constant volume gas thermometer is 70 kPa at the ice point.  Find the pressure at the steam point.


In a Callender's compensated  constant pressure air thermometer, the volume of the bulb is 1800 cc. When the bulb is kept immersed in a vessel, 200 cc of mercury has to be poured out. Calculate the temperature of the vessel.


A platinum resistance thermometer reads 0° when its resistance is 80 Ω and 100° when its resistance is 90 Ω.
Find the temperature at the platinum scale at which the resistance is 86 Ω.


Two metre scales, one of steel and the other of aluminium, agree at 20°C. Calculate the ratio aluminium-centimetre/steel-centimetre at (a) 0°C, (b) 40°C and (c) 100°C. α for steel = 1.1 × 10–5 °C–1 and for aluminium = 2.3 × 10–5°C–1.


A metre scale made of steel reads accurately at 20°C. In a sensitive experiment, distances accurate up to 0.055 mm in 1 m are required. Find the range of temperature in which the experiment can be performed with this metre scale. Coefficient of linear expansion of steel  = 11 × 10–6 °C–1.


A steel rod is rigidly clamped at its two ends. The rod is under zero tension at 20°C. If the temperature rises to 100°C, what force will the rod exert on one of the clamps? Area of cross-section of the rod is 2.00 mm2. Coefficient of linear expansion of steel is 12.0 × 10–6 °C–1 and Young's modulus of steel is 2.00 × 1011 Nm–2.


A ball is dropped on a floor from a height of 2.0 m. After the collision it rises up to a height of 1.5 m. Assume that 40% of the mechanical energy lost goes as thermal energy into the ball. Calculate the rise in the temperature of the ball in the collision. Heat capacity of the ball is 800 J K−1.


A copper cube of mass 200 g slides down on a rough inclined plane of inclination 37° at a constant speed. Assume that any loss in mechanical energy goes into the copper block as thermal energy. Find the increase in the temperature of the block as it slides down through 60 cm. Specific heat capacity of copper = 420 J kg−1 K−1.


Two steel rods and an aluminium rod of equal length l0 and equal cross-section are joined rigidly at their ends, as shown in the figure below. All the rods are in a state of zero tension at 0°C. Find the length of the system when the temperature is raised to θ. Coefficient of linear expansion of aluminium and steel are αa and αs, respectively. Young's modulus of aluminium is Ya and of steel is Ys

Steel
Aluminium
Steel

The graph between two temperature scales A and B is shown in figure. Between upper fixed point and lower fixed point there are 150 equal division on scale A and 100 on scale B. The relationship for conversion between the two scales is given by ______.


Share
Notifications

Englishहिंदीमराठी


      Forgot password?
Use app×