Advertisements
Advertisements
प्रश्न
In an AC series circuit, the instantaneous currt is zero when the instantaneous voltage is maximum. Connected to the source may be a
(a) pure inductor
(b) pure capacitor
(c) pure resistor
(d) combination of an inductor and a capacitor
उत्तर
(a) pure inductor
(b) pure capacitor
(d) combination of an inductor and a capacitor.
For a pure inductive circuit, voltage leads the current by 90°. So, the instantaneous current is zero when the instantaneous voltage is maximum.
Similar is the case with a purely capacitive circuit, in which, current leads the voltage by 90°
Also, in a circuit containing a combination of inductor and capacitor, the current may lead or lag the voltage by 90°, depending upon whether the voltage across the inductor or the capacitor is greater. Here too, there is a phase difference of 90° between the voltage and current. Hence, the the instantaneous current is zero when the instantaneous voltage is maximum.
APPEARS IN
संबंधित प्रश्न
An a.c. source of voltage V = V0 sin ωt is connected to a series combination of L, C, and R. Use the phasor diagram to obtain the expression for an impedance of a circuit and the phase angle between voltage and current. Find the condition when current will be in phase with the voltage. What is the circuit in this condition called?
Prove theoretically the relation between e.m.f. induced in a coil and rate of change of magnetic flux in electromagnetic induction.
An alternating emf of 220 V is applied to a circuit containing a resistor R having the resistance of 160Ω and a capacitor ‘C’ is series. The current is found to lead the supply voltage by an angle
`θ = tan^(-1) ("3/4")`
a) Calculate
1) The capacitive reactance
2) The impedance of the circuit
3) Current flowing in the circuit
b) If the frequency of the applied emf is 50 Hz, what is the value of the capacitance of the capacitor ‘C’?
Define the quality factor in an a.c. circuit. Why should the quality factor have high value in receiving circuits? Name the factors on which it depends.
A resistance is connected to an AC source. If a capacitor is included in the series circuit, will the average power absorbed by the resistance increase or decrease? If an inductor of small inductance is also included in the series circuit, will the average power absorbed increase or decrease further?
Transformers are used ______.
The current in a discharging LR circuit is given by i = i0 e−t/τ , where τ is the time constant of the circuit. Calculate the rms current for the period t = 0 to t = τ.
A coil has a resistance of 10 Ω and an inductance of 0.4 henry. It is connected to an AC source of 6.5 V, `30/pi Hz`. Find the average power consumed in the circuit.
An electric bulb is designed to consume 55 W when operated at 110 volts. It is connected to a 220 V, 50 Hz line through a choke coil in series. What should be the inductance of the coil for which the bulb gets correct voltage?
Following figure shows a typical circuit for a low-pass filter. An AC input Vi = 10 mV is applied at the left end and the output V0 is received at the right end. Find the output voltage for ν = 10 k Hz, 1.0 MHz and 10.0 MHz. Note that as the frequency is increased the output decreases and, hence, the name low-pass filter.
In which of the following circuits the maximum power dissipation is observed?
Quality factor and power factor both have the dimensions of ______.
The power factor of series LCR circuit when at resistance is
The power factor of an a.c circuit having resistance R and inductance L Connected in series to an a.c source of angular frequency co is.
The series combination of R, L, C is connected to an a.c. source. If the resistance is 3 and the reactance is 4, the power factor of the circuit is:
In the series LCR circuit, the power dissipation is through ______
The coefficient of induction of a choke coil is 0.1 H and resistance is 12 Ω. If it is connected to an a.c source of frequency 60Hz. Then the power factor will be ______.
An alternating current generator has an internal resistance Rg and an internal reactance Xg. It is used to supply power to a passive load consisting of a resistance Rg and a reactance XL. For maximum power to be delivered from the generator to the load, the value of XL is equal to ______.
An inductor of reactance 1 Ω and a resistor of 2 Ω are connected in series to the terminals of a 6 V (rms) a.c. source. The power dissipated in the circuit is ______.
