Advertisements
Advertisements
प्रश्न
Prove theoretically the relation between e.m.f. induced in a coil and rate of change of magnetic flux in electromagnetic induction.
उत्तर
1)
Magnetic flux Φ = NABcos ωt
N → No.s of turns
A → Area of a coil
B → Magnetic field {external}
ω → Angular speed of the coil
`:. max phi_0 = NAB, omegat -> 0`
`:.phi = phi_0 cos omegat`
induce EMF(e)
e = `-(dphi)/(dt) = + omegaNAB sin omegat`
`e_0 = omegaNAB, omegat -> 90`
`:. e = e_0 sin omegat`
So there is phase difference of `pi/2` with `phi` and e
APPEARS IN
संबंधित प्रश्न
Ajit had a high tension tower erected on his farm land. He kept complaining to the authorities to remove it as it was occupying a large portion of his land. His uncle, who was a teacher, explained to him the need for erecting these towers for efficient transmission of power. As Ajit realised its significance, he stopped complaining.
Answer the following questions:
(a) Why is it necessary to transport power at high voltage?
(b) A low power factor implies large power loss. Explain.
(c) Write two values each displayed by Ajit and his uncle.
Define the quality factor in an a.c. circuit. Why should the quality factor have high value in receiving circuits? Name the factors on which it depends.
In a circuit, containing a capacitor and an AC source, the current is zero at the instant the source voltage is maximum. Is it consistent with Ohm's Law?
A resistance is connected to an AC source. If a capacitor is included in the series circuit, will the average power absorbed by the resistance increase or decrease? If an inductor of small inductance is also included in the series circuit, will the average power absorbed increase or decrease further?
A series AC circuit has a resistance of 4 Ω and a reactance of 3 Ω. The impedance of the circuit is
An AC source rated 100 V (rms) supplies a current of 10 A (rms) to a circuit. The average power delivered by the source
(a) must be 1000 W
(b) may be 1000 W
(c) may be greater than 1000 W
(d) may be less than 1000 W
The current in a discharging LR circuit is given by i = i0 e−t/τ , where τ is the time constant of the circuit. Calculate the rms current for the period t = 0 to t = τ.
Consider the situation of the previous problem. Find the average electric field energy stored in the capacitor and the average magnetic field energy stored in the coil.
What is the value of power factor for a pure resistor connected to an alternating current source ?
An ac circuit as shown in the figure has an inductor of inductance L and a resistor of resistance R connected in series. Using the phasor diagram, explain why the voltage in the circuit will lead the current in phase.
Answer the following question.
Show that an ideal inductor does not dissipate power in an ac circuit.
In previous questions 3 and 4, what is the net power absorbed by each circuit over a complete cycle. Explain your answer.
Suppose the circuit has a resistance of 15 Ω. Obtain the average power transferred to each element of the circuit, and the total power absorbed.
The power factor in a circuit connected to an A.C. The value of power factor is ______.
Quality factor and power factor both have the dimensions of ______.
The power factor of series LCR circuit when at resistance is
The power factor of an a.c circuit having resistance R and inductance L Connected in series to an a.c source of angular frequency co is.
The series combination of R, L, C is connected to an a.c. source. If the resistance is 3 and the reactance is 4, the power factor of the circuit is:
In an AC. circuit, the current is :
i = `5 sin (100t - pi/2)` amp.
and the a.c. potentiol is:
V = 200 sin (100t) volt.
Then the power consumption is
A 100 Ω electric iron is connected to 200 V, 50 Hz ac source. Calculate average power delivered to iron, peak power and energy spent in one minute?
In the series LCR circuit, the power dissipation is through ______
An alternating current generator has an internal resistance Rg and an internal reactance Xg. It is used to supply power to a passive load consisting of a resistance Rg and a reactance XL. For maximum power to be delivered from the generator to the load, the value of XL is equal to ______.
An inductor of reactance 1 Ω and a resistor of 2 Ω are connected in series to the terminals of a 6 V (rms) a.c. source. The power dissipated in the circuit is ______.
